Just How to Install a Bath Tub Yourself
Just How to Install a Bath Tub Yourself
Blog Article
Have you been searching for suggestions around Installing A Bathtub?
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately hard project. If the old tub is conveniently available, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. See to it you have qualified yourself for the work and are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new tub in your washroom if you have actually currently acquired a new tub as well as don't require to transform the setup of your previous water supply pipes.
Your tools and material checklist must consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, position the bathtub in the called for position. The wood boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leakages and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's instruction manual. Tiling and securing around the bath tub should wait until the tub has actually been used at least when as this will certainly resolve it into its final setting.
Planning for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps system to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a rigid seal, causing the water to pass through the wall surface in between the bath and the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break fairly very early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up on A Step-by-Step Guide to Installing a Bathtub from an acquaintance on our other web address. Loved our review? Please share it. Help another person find it. Thank you for your time invested reading it.
Browse Our Site
Report this page